Documentation Home
MySQL 8.4 Reference Manual
Related Documentation Download this Manual
PDF (US Ltr) - 40.0Mb
PDF (A4) - 40.0Mb
Man Pages (TGZ) - 258.6Kb
Man Pages (Zip) - 365.7Kb
Info (Gzip) - 4.0Mb
Info (Zip) - 4.0Mb


MySQL 8.4 Reference Manual  /  ...  /  RESET BINARY LOGS AND GTIDS Statement

15.4.1.2 RESET BINARY LOGS AND GTIDS Statement

Note

This statement takes the place of the old RESET MASTER statement, which is no longer supported.

RESET BINARY LOGS AND GTIDS [TO binary_log_file_index_number]
Warning

Use this statement with caution to ensure you do not lose any wanted binary log file data and GTID execution history.

RESET BINARY LOGS AND GTIDS requires the RELOAD privilege.

For a server where binary logging is enabled (log_bin is ON), RESET BINARY LOGS AND GTIDS deletes all existing binary log files and resets the binary log index file, resetting the server to its state before binary logging was started. A new empty binary log file is created so that binary logging can be restarted.

For a server where GTIDs are in use (gtid_mode is ON), issuing RESET BINARY LOGS AND GTIDS resets the GTID execution history. The value of the gtid_purged system variable is set to an empty string (''), the global value (but not the session value) of the gtid_executed system variable is set to an empty string, and the mysql.gtid_executed table is cleared (see mysql.gtid_executed Table). If the GTID-enabled server has binary logging enabled, RESET BINARY LOGS AND GTIDS also resets the binary log as described above. Note that RESET BINARY LOGS AND GTIDS is the method to reset the GTID execution history even if the GTID-enabled server is a replica where binary logging is disabled; RESET REPLICA has no effect on the GTID execution history. For more information on resetting the GTID execution history, see Resetting the GTID Execution History.

Issuing RESET BINARY LOGS AND GTIDS without the optional TO clause deletes all binary log files listed in the index file, resets the binary log index file to be empty, and creates a new binary log file starting at 1. Use the optional TO clause to start the binary log file index from a number other than 1 after the reset.

Check that you are using a reasonable value for the index number. If you enter an incorrect value, you can correct this by issuing another RESET BINARY LOGS AND GTIDS statement with or without the TO clause. If you do not correct a value that is out of range, the server cannot be restarted.

The following example demonstrates TO clause usage:

RESET BINARY LOGS AND GTIDS TO 1234;

SHOW BINARY LOGS;
+-------------------+-----------+-----------+
| Log_name          | File_size | Encrypted |
+-------------------+-----------+-----------+
| source-bin.001234 |       154 | No        |
+-------------------+-----------+-----------+
Important

The effects of RESET BINARY LOGS AND GTIDS without the TO clause differ from those of PURGE BINARY LOGS in 2 key ways:

  1. RESET BINARY LOGS AND GTIDS removes all binary log files that are listed in the index file, leaving only a single, empty binary log file with a numeric suffix of .000001, whereas the numbering is not reset by PURGE BINARY LOGS.

  2. RESET BINARY LOGS AND GTIDS is not intended to be used while any replicas are running. The behavior of RESET BINARY LOGS AND GTIDS when used while replicas are running is undefined (and thus unsupported), whereas PURGE BINARY LOGS may be safely used while replicas are running.

See also Section 15.4.1.1, “PURGE BINARY LOGS Statement”.

RESET BINARY LOGS AND GTIDS without the TO clause can prove useful when you first set up a source and replica, so that you can verify the setup as follows:

  1. Start the source and replica, and start replication (see Section 19.1.2, “Setting Up Binary Log File Position Based Replication”).

  2. Execute a few test queries on the source.

  3. Check that the queries were replicated to the replica.

  4. When replication is running correctly, issue STOP REPLICA followed by RESET REPLICA (both on the replica), then verify that no unwanted data from the test queries exists on the replica. Following this, issue RESET BINARY LOGS AND GTIDS (also on the replica) to remove binary logs and and associated transaction IDs.

  5. Remove the unwanted data from the source, then issue RESET BINARY LOGS AND GTIDS to purge any binary log entries and identifiers associated with it.

After verifying the setup, resetting the source and replica and ensuring that no unwanted data or binary log files generated by testing remain on the source or replica, you can start the replica and begin replicating.