Documentation Home
MySQL 8.4 Reference Manual
Related Documentation Download this Manual
PDF (US Ltr) - 39.9Mb
PDF (A4) - 40.0Mb
Man Pages (TGZ) - 258.5Kb
Man Pages (Zip) - 365.5Kb
Info (Gzip) - 4.0Mb
Info (Zip) - 4.0Mb

MySQL 8.4 Reference Manual  /  ...  /  Installing Semisynchronous Replication Installing Semisynchronous Replication

Semisynchronous replication is implemented using plugins, which must be installed on the source and on the replicas to make semisynchronous replication available on the instances. There are different plugins for a source and for a replica. After a plugin has been installed, you control it by means of the system variables associated with it. These system variables are available only when the associated plugin has been installed.

This section describes how to install the semisynchronous replication plugins. For general information about installing plugins, see Section 7.6.1, “Installing and Uninstalling Plugins”.

To use semisynchronous replication, the following requirements must be satisfied:

The file name suffix for the plugin library files differs per platform (for example, .so for Unix and Unix-like systems, and .dll for Windows). The plugin and library file names are as follows:

  • Source server: rpl_semi_sync_source plugin ( or semisync_source.dll library)

  • Replica: rpl_semi_sync_replica plugin ( or semisync_replica.dll library)

To be usable by a source or replica server, the appropriate plugin library file must be located in the MySQL plugin directory (the directory named by the plugin_dir system variable). If necessary, configure the plugin directory location by setting the value of plugin_dir at server startup. The source plugin library file must be present in the plugin directory of the source server. The replica plugin library file must be present in the plugin directory of each replica server.

To set up semisynchronous replication, use the following instructions. The INSTALL PLUGIN, SET GLOBAL, STOP REPLICA, and START REPLICA statements mentioned here require the REPLICATION_SLAVE_ADMIN privilege (or the deprecated SUPER privilege).

To load the plugins, use the INSTALL PLUGIN statement on the source and on each replica that is to be semisynchronous, adjusting the .so suffix for your platform as necessary.

On the source:

INSTALL PLUGIN rpl_semi_sync_source SONAME '';

On each replica:

INSTALL PLUGIN rpl_semi_sync_replica SONAME '';

If an attempt to install a plugin results in an error on Linux similar to that shown here, you must install libimf:

mysql> INSTALL PLUGIN rpl_semi_sync_source SONAME '';
ERROR 1126 (HY000): Can't open shared library
(errno: 22 cannot open shared object file:
No such file or directory)

You can obtain libimf from

To verify plugin installation, examine the Information Schema PLUGINS table or use the SHOW PLUGINS statement (see Section 7.6.2, “Obtaining Server Plugin Information”). For example:

       WHERE PLUGIN_NAME LIKE '%semi%';
| rpl_semi_sync_source | ACTIVE        |

If a plugin fails to initialize, check the server error log for diagnostic messages.

After a semisynchronous replication plugin has been installed, it is disabled by default. The plugins must be enabled both on the source side and the replica side to enable semisynchronous replication. If only one side is enabled, replication is asynchronous. To enable the plugins, set the appropriate system variable either at runtime using SET GLOBAL, or at server startup on the command line or in an option file. For example:

SET GLOBAL rpl_semi_sync_source_enabled = 1;
SET GLOBAL rpl_semi_sync_replica_enabled = 1;

If you enable semisynchronous replication on a replica at runtime, you must also start the replication I/O (receiver) thread (stopping it first if it is already running) to cause the replica to connect to the source and register as a semisynchronous replica:


If the replication I/O (receiver) thread is already running and you do not restart it, the replica continues to use asynchronous replication.

A setting listed in an option file takes effect each time the server starts. For example, you can set the variables in my.cnf files on the source and replica servers as follows. On the source:


On each replica:


You can configure the behavior of the semisynchronous replication plugins using the system variables that become available when you install the plugins. For information on key system variables, see Section, “Configuring Semisynchronous Replication”.