To be useful, backups must be scheduled regularly. A full backup
(a snapshot of the data at a point in time) can be done in MySQL
with several tools. For example,
Backup can perform a
physical backup of
an entire instance, with optimizations to minimize overhead and
avoid disruption when backing up
files; mysqldump provides online
logical backup. This
discussion uses mysqldump.
Assume that we make a full backup of all our
InnoDB tables in all databases using the
following command on Sunday at 1 p.m., when load is low:
$> mysqldump --all-databases --master-data --single-transaction > backup_sunday_1_PM.sql
.sql file produced by
mysqldump contains a set of SQL
INSERT statements that can be
used to reload the dumped tables at a later time.
This backup operation acquires a global read lock on all tables
at the beginning of the dump (using
TABLES WITH READ LOCK). As soon as this lock has been
acquired, the binary log coordinates are read and the lock is
released. If long updating statements are running when the
FLUSH statement is issued, the
backup operation may stall until those statements finish. After
that, the dump becomes lock-free and does not disturb reads and
writes on the tables.
It was assumed earlier that the tables to back up are
InnoDB tables, so
--single-transaction uses a
consistent read and guarantees that data seen by
mysqldump does not change. (Changes made by
other clients to
InnoDB tables are not seen
by the mysqldump process.) If the backup
operation includes nontransactional tables, consistency requires
that they do not change during the backup. For example, for the
MyISAM tables in the
database, there must be no administrative changes to MySQL
accounts during the backup.
Full backups are necessary, but it is not always convenient to create them. They produce large backup files and take time to generate. They are not optimal in the sense that each successive full backup includes all data, even that part that has not changed since the previous full backup. It is more efficient to make an initial full backup, and then to make incremental backups. The incremental backups are smaller and take less time to produce. The tradeoff is that, at recovery time, you cannot restore your data just by reloading the full backup. You must also process the incremental backups to recover the incremental changes.
To make incremental backups, we need to save the incremental
changes. In MySQL, these changes are represented in the binary
log, so the MySQL server should always be started with the
--log-bin option to enable that
log. With binary logging enabled, the server writes each data
change into a file while it updates data. Looking at the data
directory of a MySQL server that was started with the
--log-bin option and that has
been running for some days, we find these MySQL binary log
-rw-rw---- 1 guilhem guilhem 1277324 Nov 10 23:59 gbichot2-bin.000001 -rw-rw---- 1 guilhem guilhem 4 Nov 10 23:59 gbichot2-bin.000002 -rw-rw---- 1 guilhem guilhem 79 Nov 11 11:06 gbichot2-bin.000003 -rw-rw---- 1 guilhem guilhem 508 Nov 11 11:08 gbichot2-bin.000004 -rw-rw---- 1 guilhem guilhem 220047446 Nov 12 16:47 gbichot2-bin.000005 -rw-rw---- 1 guilhem guilhem 998412 Nov 14 10:08 gbichot2-bin.000006 -rw-rw---- 1 guilhem guilhem 361 Nov 14 10:07 gbichot2-bin.index
Each time it restarts, the MySQL server creates a new binary log
file using the next number in the sequence. While the server is
running, you can also tell it to close the current binary log
file and begin a new one manually by issuing a
FLUSH LOGS SQL statement or with
a mysqladmin flush-logs command.
mysqldump also has an option to flush the
.index file in the data directory
contains the list of all MySQL binary logs in the directory.
The MySQL binary logs are important for recovery because they form the set of incremental backups. If you make sure to flush the logs when you make your full backup, the binary log files created afterward contain all the data changes made since the backup. Let's modify the previous mysqldump command a bit so that it flushes the MySQL binary logs at the moment of the full backup, and so that the dump file contains the name of the new current binary log:
$> mysqldump --single-transaction --flush-logs --master-data=2 \ --all-databases > backup_sunday_1_PM.sql
After executing this command, the data directory contains a new
binary log file,
option causes the server to flush its logs. The
--master-data option causes
mysqldump to write binary log information to
its output, so the resulting
.sql dump file
includes these lines:
-- Position to start replication or point-in-time recovery from -- CHANGE MASTER TO MASTER_LOG_FILE='gbichot2-bin.000007',MASTER_LOG_POS=4;
Because the mysqldump command made a full backup, those lines mean two things:
The dump file contains all changes made before any changes written to the
gbichot2-bin.000007binary log file or higher.
All data changes logged after the backup are not present in the dump file, but are present in the
gbichot2-bin.000007binary log file or higher.
On Monday at 1 p.m., we can create an incremental backup by
flushing the logs to begin a new binary log file. For example,
executing a mysqladmin flush-logs command
gbichot2-bin.000008. All changes
between the Sunday 1 p.m. full backup and Monday 1 p.m. are in
gbichot2-bin.000007 file. This
incremental backup is important, so it is a good idea to copy it
to a safe place. (For example, back it up on tape or DVD, or
copy it to another machine.) On Tuesday at 1 p.m., execute
another mysqladmin flush-logs command. All
changes between Monday 1 p.m. and Tuesday 1 p.m. are in the
gbichot2-bin.000008 file (which also should
be copied somewhere safe).
The MySQL binary logs take up disk space. To free up space, purge them from time to time. One way to do this is by deleting the binary logs that are no longer needed, such as when we make a full backup:
$> mysqldump --single-transaction --flush-logs --master-data=2 \ --all-databases --delete-master-logs > backup_sunday_1_PM.sql
Deleting the MySQL binary logs with mysqldump
--delete-master-logs can be dangerous if your server
is a replication source server, because replica servers might
not yet fully have processed the contents of the binary log.
The description for the
LOGS statement explains what should be verified
before deleting the MySQL binary logs. See
PURGE BINARY LOGS Statement.