Installing a new version of MySQL may require upgrading these parts of the existing installation:
mysqlsystem schema, which contains tables that store information required by the MySQL server as it runs (see Section 7.3, “The mysql System Schema”).
mysqlschema tables fall into two broad categories:
Data dictionary tables, which store database object metadata.
System tables (that is, the remaining non-data dictionary tables), which are used for other operational purposes.
Other schemas, some of which are built in and may be considered “owned” by the server, and others which are not:
Two distinct version numbers are associated with parts of the installation that may require upgrading:
The data dictionary version. This applies to the data dictionary tables.
The server version, also known as the MySQL version. This applies to the system tables and objects in other schemas.
In both cases, the actual version applicable to the existing MySQL installation is stored in the data dictionary, and the current expected version is compiled into the new version of MySQL. When an actual version is lower than the current expected version, those parts of the installation associated with that version must be upgraded to the current version. If both versions indicate an upgrade is needed, the data dictionary upgrade must occur first.
As a reflection of the two distinct versions just mentioned, the upgrade occurs in two steps:
Step 1: Data dictionary upgrade.
This step upgrades:
The data dictionary tables in the
mysqlschema. If the actual data dictionary version is lower than the current expected version, the server creates data dictionary tables with updated definitions, copies persisted metadata to the new tables, atomically replaces the old tables with the new ones, and reinitializes the data dictionary.
The Performance Schema,
Step 2: Server upgrade.
This step comprises all other upgrade tasks. If the server version of the existing MySQL installation is lower than that of the new installed MySQL version, everything else must be upgraded:
The system tables in the
mysqlschema (the remaining non-data dictionary tables).
The data dictionary upgrade (step 1) is the responsibility of the
server, which performs this task as necessary at startup unless
invoked with an option that prevents it from doing so. The option
If the data dictionary is out of date but the server is prevented from upgrading it, the server does not run, and exits with an error instead. For example:
[ERROR] [MY-013381] [Server] Server shutting down because upgrade is
required, yet prohibited by the command line option '--upgrade=NONE'.
[ERROR] [MY-010334] [Server] Failed to initialize DD Storage Engine
[ERROR] [MY-010020] [Server] Data Dictionary initialization failed.
--upgrade server option
controls whether and how the server performs an automatic upgrade
With no option or with
--upgrade=AUTO, the server upgrades anything it determines to be out of date (steps 1 and 2).
--upgrade=NONE, the server upgrades nothing (skips steps 1 and 2), but also exits with an error if the data dictionary must be upgraded. It is not possible to run the server with an out-of-date data dictionary; the server insists on either upgrading it or exiting.
--upgrade=MINIMAL, the server upgrades the data dictionary, the Performance Schema, and the
INFORMATION_SCHEMA, if necessary (step 1). Note that following an upgrade with this option, Group Replication cannot be started, because system tables on which the replication internals depend are not updated, and reduced functionality might also be apparent in other areas.
--upgrade=FORCE, the server upgrades the data dictionary, the Performance Schema, and the
INFORMATION_SCHEMA, if necessary (step 1), and forces an upgrade of everything else (step 2). Expect server startup to take longer with this option because the server checks all objects in all schemas.
FORCE is useful to force step 2 actions to be
performed if the server thinks they are not necessary. One way
FORCE differs from
is that with
FORCE, the server re-creates
system tables such as help tables or time zone tables if they are
Additional notes about what occurs during upgrade step 2:
Step 2 installs the
sysschema if it is not installed, and upgrades it to the current version otherwise. An error occurs if a
sysschema exists but has no
versionview, on the assumption that its absence indicates a user-created schema:
A sys schema exists with no sys.version view. If you have a user created sys schema, this must be renamed for the upgrade to succeed.
To upgrade in this case, remove or rename the existing
sysschema first. Then perform the upgrade procedure again. (It may be necessary to force step 2.)
To prevent the
sysschema check, start the server with the
Step 2 upgrades the system tables to ensure that they have the current structure, and this includes the help tables but not the time zone tables. The procedure for loading time zone tables is platform dependent and requires decision making by the DBA, so it cannot be done automatically.
When Step 2 is upgrading the system tables in the
mysqlschema, the column order in the primary key of the
mysql.procs_privtables is changed to place the host name and user name columns together. Placing the host name and user name together means that index lookup can be used, which improves performance for
DROP USER, and
RENAME USERstatements, and for ACL checks for multiple users with multiple privileges. Dropping and re-creating the index is necessary and might take some time if the system has a large number of users and privileges.
Step 2 processes all tables in all user schemas as necessary. Table checking might take a long time to complete. Each table is locked and therefore unavailable to other sessions while it is being processed. Check and repair operations can be time-consuming, particularly for large tables. Table checking uses the
FOR UPGRADEoption of the
CHECK TABLEstatement. For details about what this option entails, see Section 18.104.22.168, “CHECK TABLE Statement”.
To prevent table checking, start the server with the
To force table checking, start the server with the
Step 2 saves the MySQL version number in a file named
mysql_upgrade_infoin the data directory.
To ignore the
mysql_upgrade_infofile and perform the check regardless, start the server with the
mysql_upgrade_infofile is deprecated; expect it to be removed in a future version of MySQL.
Step 2 marks all checked and repaired tables with the current MySQL version number. This ensures that the next time upgrade checking occurs with the same version of the server, it can be determined whether there is any need to check or repair a given table again.