25.5.31 ndb_waiter — Wait for NDB Cluster to Reach a Given Status

ndb_waiter repeatedly (each 100 milliseconds) prints out the status of all cluster data nodes until either the cluster reaches a given status or the --timeout limit is exceeded, then exits. By default, it waits for the cluster to achieve STARTED status, in which all nodes have started and connected to the cluster. This can be overridden using the --no-contact and --not-started options.

The node states reported by this utility are as follows:

• NO_CONTACT: The node cannot be contacted.

• UNKNOWN: The node can be contacted, but its status is not yet known. Usually, this means that the node has received a START or RESTART command from the management server, but has not yet acted on it.

• NOT_STARTED: The node has stopped, but remains in contact with the cluster. This is seen when restarting the node using the management client's RESTART command.

• STARTING: The node's ndbd process has started, but the node has not yet joined the cluster.

• STARTED: The node is operational, and has joined the cluster.

• SHUTTING_DOWN: The node is shutting down.

• SINGLE USER MODE: This is shown for all cluster data nodes when the cluster is in single user mode.

Options that can be used with ndb_waiter are shown in the following table. Additional descriptions follow the table.

Table 25.51 Command-line options used with the program ndb_waiter

Format	Description	Added, Deprecated, or Removed
--connect-retries=#	Number of times to retry connection before giving up	(Supported in all NDB releases based on MySQL 8.3)
--connect-retry-delay=#	Number of seconds to wait between attempts to contact management server	(Supported in all NDB releases based on MySQL 8.3)
--connect-string=connection_string, -c connection_string	Same as --ndb-connectstring	(Supported in all NDB releases based on MySQL 8.3)
--defaults-extra-file=path	Read given file after global files are read	(Supported in all NDB releases based on MySQL 8.3)
--defaults-file=path	Read default options from given file only	(Supported in all NDB releases based on MySQL 8.3)
--defaults-group-suffix=string	Also read groups with concat(group, suffix)	(Supported in all NDB releases based on MySQL 8.3)
--help, -?	Display help text and exit	(Supported in all NDB releases based on MySQL 8.3)
--login-path=path	Read given path from login file	(Supported in all NDB releases based on MySQL 8.3)
--no-login-paths	Do not read login paths from the login path file	(Supported in all NDB releases based on MySQL 8.3)
--ndb-connectstring=connection_string, -c connection_string	Set connect string for connecting to ndb_mgmd. Syntax: "[nodeid=id;][host=]hostname[:port]". Overrides entries in NDB_CONNECTSTRING and my.cnf	(Supported in all NDB releases based on MySQL 8.3)
--ndb-mgm-tls=level	ndb_mgm client TLS requirement level	ADDED: 8.3.0
--ndb-mgmd-host=connection_string, -c connection_string	Same as --ndb-connectstring	(Supported in all NDB releases based on MySQL 8.3)
--ndb-tls-search-path=list	List of directories containing TLS keys and certificates	ADDED: 8.3.0
--no-contact, -n	Wait for cluster to reach NO CONTACT state	(Supported in all NDB releases based on MySQL 8.3)
--no-defaults	Do not read default options from any option file other than login file	(Supported in all NDB releases based on MySQL 8.3)
--not-started	Wait for cluster to reach NOT STARTED state	(Supported in all NDB releases based on MySQL 8.3)
--nowait-nodes=list	List of nodes not to be waited for	(Supported in all NDB releases based on MySQL 8.3)
--print-defaults	Print program argument list and exit	(Supported in all NDB releases based on MySQL 8.3)
--single-user	Wait for cluster to enter single user mode	(Supported in all NDB releases based on MySQL 8.3)
--timeout=#, -t #	Wait this many seconds, then exit whether or not cluster has reached desired state	(Supported in all NDB releases based on MySQL 8.3)
--usage, -?	Display help text and exit; same as --help	(Supported in all NDB releases based on MySQL 8.3)
--version, -V	Display version information and exit	(Supported in all NDB releases based on MySQL 8.3)
--wait-nodes=list, -w list	List of nodes to be waited for	(Supported in all NDB releases based on MySQL 8.3)

Usage

ndb_waiter [-c connection_string]

Additional Options

• --character-sets-dir

  Command-Line Format	--character-sets-dir=path

  Directory containing character sets.

• --connect-retries

  Command-Line Format	--connect-retries=#
  Type	Integer
  Default Value	12
  Minimum Value	0
  Maximum Value	12

  Number of times to retry connection before giving up.

• --connect-retry-delay

  Command-Line Format	--connect-retry-delay=#
  Type	Integer
  Default Value	5
  Minimum Value	0
  Maximum Value	5

  Number of seconds to wait between attempts to contact management server.

• --connect-string

  Command-Line Format	--connect-string=connection_string
  Type	String
  Default Value	[none]

  Same as --ndb-connectstring.

• --core-file

  Command-Line Format	--core-file

  Write core file on error; used in debugging.

• --defaults-extra-file

  Command-Line Format	--defaults-extra-file=path
  Type	String
  Default Value	[none]

  Read given file after global files are read.

• --defaults-file

  Command-Line Format	--defaults-file=path
  Type	String
  Default Value	[none]

  Read default options from given file only.

• --defaults-group-suffix

  Command-Line Format	--defaults-group-suffix=string
  Type	String
  Default Value	[none]

  Also read groups with concat(group, suffix).

• --login-path

  Command-Line Format	--login-path=path
  Type	String
  Default Value	[none]

  Read given path from login file.

• --no-login-paths

  Command-Line Format	--no-login-paths

  Skips reading options from the login path file.

• --help

  Command-Line Format	--help

  Display help text and exit.

• --ndb-connectstring

  Command-Line Format	--ndb-connectstring=connection_string
  Type	String
  Default Value	[none]

  Set connection string for connecting to ndb_mgmd. Syntax: [nodeid=id;][host=]hostname[:port]. Overrides entries in NDB_CONNECTSTRING and my.cnf.

• --ndb-mgm-tls

  Command-Line Format	--ndb-mgm-tls=level
  Type	Enumeration
  Default Value	relaxed
  Valid Values	relaxed strict

  Sets the level of TLS support required to connect to the management server; one of relaxed or strict. relaxed (the default) means that a TLS connection is attempted, but success is not required; strict means that TLS is required to connect.

• --ndb-mgmd-host

  Command-Line Format	--ndb-mgmd-host=connection_string
  Type	String
  Default Value	[none]

  Same as --ndb-connectstring.

• --ndb-nodeid

  Command-Line Format	--ndb-nodeid=#
  Type	Integer
  Default Value	[none]

  Set node ID for this node, overriding any ID set by --ndb-connectstring.

• --ndb-optimized-node-selection

  Command-Line Format	--ndb-optimized-node-selection

  Enable optimizations for selection of nodes for transactions. Enabled by default; use --skip-ndb-optimized-node-selection to disable.

• --ndb-tls-search-path

  Command-Line Format	--ndb-tls-search-path=list
  Type	Path name
  Default Value (Unix)	$HOME/ndb-tls
  Default Value (Windows)	$HOMEDIR/ndb-tls

  Specify a list of directories to search for a CA file. On Unix platforms, the directory names are separated by colons (:); on Windows systems, the semicolon character (;) is used as the separator. A directory reference may be relative or absolute; it may contain one or more environment variables, each denoted by a prefixed dollar sign ($), and expanded prior to use.

  Searching begins with the leftmost named directory and proceeds from left to right until a file is found. An empty string denotes an empty search path, which causes all searches to fail. A string consisting of a single dot (.) indicates that the search path limited to the current working directory.

  If no search path is supplied, the compiled-in default value is used. This value depends on the platform used: On Windows, this is \ndb-tls; on other platforms (including Linux), it is $HOME/ndb-tls. This can be overridden by compiling NDB Cluster using -DWITH_NDB_TLS_SEARCH_PATH.

• --no-contact, -n

  Instead of waiting for the STARTED state, ndb_waiter continues running until the cluster reaches NO_CONTACT status before exiting.

• --no-defaults

  Command-Line Format	--no-defaults

  Do not read default options from any option file other than login file.

• --not-started

  Instead of waiting for the STARTED state, ndb_waiter continues running until the cluster reaches NOT_STARTED status before exiting.

• --nowait-nodes=list

  When this option is used, ndb_waiter does not wait for the nodes whose IDs are listed. The list is comma-delimited; ranges can be indicated by dashes, as shown here:

  $> ndb_waiter --nowait-nodes=1,3,7-9

  Important

  Do not use this option together with the --wait-nodes option.

• --print-defaults

  Command-Line Format	--print-defaults

  Print program argument list and exit.

• --timeout=seconds, -t seconds

  Time to wait. The program exits if the desired state is not achieved within this number of seconds. The default is 120 seconds (1200 reporting cycles).

• --single-user

  The program waits for the cluster to enter single user mode.

• --usage

  Command-Line Format	--usage

  Display help text and exit; same as --help.

• --version

  Command-Line Format	--version

  Display version information and exit.

• --wait-nodes=list, -w list

  When this option is used, ndb_waiter waits only for the nodes whose IDs are listed. The list is comma-delimited; ranges can be indicated by dashes, as shown here:

  $> ndb_waiter --wait-nodes=2,4-6,10

  Important

  Do not use this option together with the --nowait-nodes option.

Sample Output.  Shown here is the output from ndb_waiter when run against a 4-node cluster in which two nodes have been shut down and then started again manually. Duplicate reports (indicated by ...) are omitted.

$> ./ndb_waiter -c localhost

Connecting to mgmsrv at (localhost)
State node 1 STARTED
State node 2 NO_CONTACT
State node 3 STARTED
State node 4 NO_CONTACT
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 UNKNOWN
State node 3 STARTED
State node 4 NO_CONTACT
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 STARTING
State node 3 STARTED
State node 4 NO_CONTACT
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 STARTING
State node 3 STARTED
State node 4 UNKNOWN
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 STARTING
State node 3 STARTED
State node 4 STARTING
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 STARTED
State node 3 STARTED
State node 4 STARTING
Waiting for cluster enter state STARTED

...

State node 1 STARTED
State node 2 STARTED
State node 3 STARTED
State node 4 STARTED
Waiting for cluster enter state STARTED

Note

If no connection string is specified, then ndb_waiter tries to connect to a management on localhost, and reports Connecting to mgmsrv at (null).