Some hardware/operating system architectures support memory pages greater than the default (usually 4KB). The actual implementation of this support depends on the underlying hardware and operating system. Applications that perform a lot of memory accesses may obtain performance improvements by using large pages due to reduced Translation Lookaside Buffer (TLB) misses.
In MySQL, large pages can be used by InnoDB, to allocate memory for its buffer pool and additional memory pool.
Currently, MySQL supports only the Linux implementation of large page support (which is called HugeTLB in Linux).
Before large pages can be used on Linux, the kernel must be
enabled to support them and it is necessary to configure the
HugeTLB memory pool. For reference, the HugeTBL API is
documented in the
Documentation/vm/hugetlbpage.txt file of
your Linux sources.
The kernel for some recent systems such as Red Hat Enterprise Linux appear to have the large pages feature enabled by default. To check whether this is true for your kernel, use the following command and look for output lines containing “huge”:
cat /proc/meminfo | grep -i hugeHugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB
The nonempty command output indicates that large page support is present, but the zero values indicate that no pages are configured for use.
If your kernel needs to be reconfigured to support large pages,
hugetlbpage.txt file for
Assuming that your Linux kernel has large page support enabled,
configure it for use by MySQL using the following commands.
Normally, you put these in an
rc file or
equivalent startup file that is executed during the system boot
sequence, so that the commands execute each time the system
starts. The commands should execute early in the boot sequence,
before the MySQL server starts. Be sure to change the allocation
numbers and the group number as appropriate for your system.
# Set the number of pages to be used. # Each page is normally 2MB, so a value of 20 = 40MB. # This command actually allocates memory, so this much # memory must be available. echo 20 > /proc/sys/vm/nr_hugepages # Set the group number that is permitted to access this # memory (102 in this case). The mysql user must be a # member of this group. echo 102 > /proc/sys/vm/hugetlb_shm_group # Increase the amount of shmem permitted per segment # (12G in this case). echo 1560281088 > /proc/sys/kernel/shmmax # Increase total amount of shared memory. The value # is the number of pages. At 4KB/page, 4194304 = 16GB. echo 4194304 > /proc/sys/kernel/shmall
For MySQL usage, you normally want the value of
shmmax to be close to the value of
To verify the large page configuration, check
/proc/meminfo again as described
previously. Now you should see some nonzero values:
cat /proc/meminfo | grep -i hugeHugePages_Total: 20 HugePages_Free: 20 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB
The final step to make use of the
hugetlb_shm_group is to give the
mysql user an “unlimited” value
for the memlock limit. This can by done either by editing
/etc/security/limits.conf or by adding the
following command to your mysqld_safe script:
ulimit -l unlimited
Large page support in MySQL is disabled by default. To enable
it, start the server with the
--large-pages option. For
example, you can use the following lines in your server's
With this option,
InnoDB uses large pages
automatically for its buffer pool and additional memory pool. If
InnoDB cannot do this, it falls back to use
of traditional memory and writes a warning to the error log:
Warning: Using conventional memory pool
To verify that large pages are being used, check
cat /proc/meminfo | grep -i hugeHugePages_Total: 20 HugePages_Free: 20 HugePages_Rsvd: 2 HugePages_Surp: 0 Hugepagesize: 4096 kB